Teledyne HDO9000 Скачать руководство пользователя страница 9

Страница: 9 / 188

Welcome

Thank you for purchasing a Teledyne LeCroy High Definition Oscilloscope. We're certain you'll be

pleased with the detailed features unique to our instruments.

The manual is arranged in the following manner:

Safety

contains important precautions and information relating to power and cooling.

Oscilloscope Overview

through

Maintenance

cover everything you need to know about the

operation and care of the instrument.

Documentation for using software options is available from the Teledyne LeCroy website at

teledynelecroy.com. Our website maintains the most current product specifications and should be

checked for frequent updates.

Take a moment to verify that all items on the packing list or invoice copy have been shipped to you.

Contact your nearest Teledyne LeCroy customer service center or national distributor if anything is

missing or damaged. We can only be responsible for replacement if you contact us immediately.

We truly hope you enjoy using Teledyne LeCroy's fine products.

Sincerely,

David C. Graef

Vice President and General Manager, Oscilloscopes

Teledyne LeCroy

vii

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды