Teledyne HDO9000 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 188

Teledyne HDO9000 Скачать руководство пользователя страница 111

Math and Measure

Measurement

Description

Fall time
(fall)

Duration of pulse waveform's falling transition from 90% to 10% of the amplitude averaged for
all falling transitions between the measurement gates. On signals not having two major levels
(triangle or saw-tooth waves, for example), top and base can default to maximum and minimum,
giving less predictable results.

Fall@level
(fall@lv)

Fall at level: Duration of pulse waveform's falling edges between user-specified transition
levels.

Threshold arguments specify two vertical values on each edge used to compute fall time:
lower = lower thresh. x amp/100 + base
upper = upper thresh. x amp/100 + base

First

Indicates value of horizontal axis at left cursor.

Frequency
(freq)

Period of cyclic signal measured as time between every other pair of 50% crossings. Starting
with first transition after left measurement gate. The period is measured for each transition pair.
The reciprocal of each period measurement is calculated as the frequency.

Freq@level
(freq@lv)

Period of cyclic signal measured as time between every other pair at the specified level. Start-
ing with first transition after left measurement gate. The period is measured for each transition
pair. The reciprocal of each period measurement is calculated as the frequency.

FWHM

Measures the width of the largest area histogram peak at half of the populationof the highest
peak.

FWxx

Measures the width of the largest area histogram peak at xx% of the population of the highest
peak.

Half Period
(hper)

Half period of a waveform.

Hist ampl
(hampl)

Difference in value between the two most populated peaks in a histogram.

Hist base

Value of the left-most of the two most populated histogram peaks.

Hist max pop

Peak with maximum population in a histogram.

Hist maximum

Value of the highest (right-most) populated bin in a histogram.

Hist mean

Average or mean value of data in a histogram.

Hist median

Value of the 'x' axis of a histogram that divides the population into two equal halves.

Hist minimum

Value of the lowest (left-most) populated bin in a histogram.

Hist mode

Position of the highest histogram peak.

Hist pop@x

Population at bin for specified horizontal coordinate.

Hist range

Calculates range (max-min) of a histogram.

Hist rms

Root mean square of the values in a histogram.

Hist sdev

Standard deviation of values in a histogram.

Hist top

Value of the right-most of the two most populated histogram peaks.

Hist X@peak

Value of the

n

th highest histogram peak. You supply the value of

n

.

Hold Time

Time from the clock edge to the data edge.

Last

Time from trigger to last (rightmost) cursor.

101

«
...
109
110
111
112
113
...
»

Содержание HDO9000





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды