Teledyne HDO9000 Скачать руководство пользователя страница 18

Страница: 18 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Single

sets Single trigger mode. The first press readies the oscilloscope to trigger. The second press

arms and triggers the oscilloscope once (single-shot acquisition) when the input signal meets the

trigger conditions.

Stop

prevents the scope from triggering on a signal. If you boot up the instrument with the trigger in

Stop

mode, a "No trace available" message is shown. Press the Auto button to display a trace.

Horizontal Controls

Turn the

Delay knob

to change the Trigger Delay value (S). Push the knob to reset Delay to zero.

If the trace source is an input channel, turn the

Horizontal Adjust knob

to set the Time/division (S) of

the oscilloscope acquisition system. The value is shown on the Timebase descriptor box. When using

this control, the oscilloscope allocates memory as needed to maintain the highest sample rate

possible for the timebase setting. If the trace source is a zoom, memory or math function, turn the

knob to change the horizontal scale of the trace, effectively "zooming" in or out. The value is shown

on the corresponding descriptor box. Push the knob to change the setting in fine increments; push it

again to return to 1, 2, 5, 10-step increments.

Vertical Controls

The front panel

Channel buttons

(1-4) turn on a channel that is off, or activate a channel that is

already on. When the channel is active, pushing its channel button turns it off. A lit button shows the

active channel (in this image, C1 is lit).

Offset knob

adjusts the zero level of the trace (this makes it appear to move up or down relative to

the center axis of the grid). The value appears on the trace descriptor box. Push it to reset Offset to

zero.

Gain knob

sets Vertical Gain (V/div). The value appears on the trace descriptor box. Push it once to

adjust V/div in fine increments; push it again to adjust in 1, 2, 5, 10-step increments.

Dig button

enables digital input on -MS models.

Math, Zoom, and Mem Buttons

The front panel

Zoom

button creates a quick zoom of each open channel trace. The resulting zoom

traces are 1/10 of the channel timebase and centered on the display. Touch the zoom trace

descriptor box to display the zoom controls and adjust this. Touch the Zoom button again to turn off

the zooms.

The

Math

and

Mem

(ory) buttons open the corresponding setup dialogs.

Cursor Controls

Cursors identify specific voltage and time values on the waveform. The white cursor markers help

make these points more visible, as well as provide a simple way to reposition them. A readout of the

values appears on the trace descriptor box.

There are five preset cursor types, each with a unique appearance on the display. These are

described in more detail in the

Cursors

section.

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды