Teledyne HDO9000 Скачать руководство пользователя страница 11

Страница: 11 / 188

Safety

To maintain the instrument in a correct and safe condition, observe generally accepted safety

procedures in addition to the precautions specified in this section.

The overall safety of any system

incorporating this product is the responsibility of the assembler of the system.

Symbols

These symbols appear on the instrument or in documentation to alert you to important safety

considerations:

Caution

of potential damage to instrument or

Warning

of potential bodily injury. Refer to the

accompanying information. Do not proceed until the information is fully understood and conditions

are met.

Caution

, high voltage; risk of electric shock or burn.

Caution

, contains parts/assemblies susceptible to damage by Electrostatic Discharge (ESD).

Frame or chassis terminal (ground connection).

Alternating current.

Standby power (front of instrument).

Precautions

Caution:

Comply with the following instructions to avoid personal injury or damage to your

equipment.

Use indoors only within the operational environment listed

. Do not use in wet or explosive

atmospheres.

Maintain ground

. This product is grounded through the power cord grounding conductor. To avoid

electric shock, connect only to a grounded mating outlet.

Connect and disconnect properly

. Do not connect/disconnect probes, test leads, or cables while they

are connected to a live voltage source.

Observe all terminal ratings

. Do not apply a voltage to any input that exceeds the maximum rating of

that input. Refer to the front of the instrument for maximum input ratings.

Use only power cord shipped with this instrument

and certified for the country of use.

Keep product surfaces clean and dry

. See

Cleaning

Do not remove the covers or inside parts

. Refer all maintenance to qualified service personnel.

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды