manualshive.com logo in svg

Teledyne HDO9000, Руководство оператора

Поделиться
Скачать
Teledyne HDO9000 Скачать руководство пользователя страница 135

Analysis Tools

When

setting up WaveScan

, you can customize the presentation by choosing different WaveScan

display features, called

Scan Views

. Optionally, set actions to occur automatically when unusual

events are found, such as stopping the acquisition or sounding an alarm.

Note:

The instrument reverts to Real-time sampling mode when WaveScan is enabled.

Scan Modes

The Scan Mode determines the type of search to be performed. Select the

Mode

along with the

Source

trace to be searched on the main WaveScan dialog. For each mode, different controls appear

on the WaveScan dialog, providing additional inputs to the search criteria. Make the appropriate

entries in these fields before starting the search.

Edge Mode

Edge Mode is used for detecting the occurrence of edges. Events that meet the threshold level are

captured and tabulated. When the acquisition is stopped, scan filters can be applied to the edges to

find specific characteristics. Edge Mode settings are:

l

Slope

. Choose Pos, Neg, or Both.

l

Level is

(set in...). Choose Percent or Absolute.

l

Percent/Absolute Level

. Enter a threshold value as a percentage of Top to Base or voltage

level.

Non-monotonic Mode

Non-monotonic Mode looks for edges that cross a threshold more than once between high and low

levels. All events that meet the criteria of slope, hysteresis, and level are presented in a table and

highlighted in the source trace. The value displayed in the table is the difference of the max. and min.

of the non-monotonicity. This can be confirmed with cursors. The hysteresis value is used to

eliminate noise. A non-monotonicity is detected only when its amplitude is greater than the

hysteresis. Therefore, when setting a hysteresis level, set a value that is greater than the amplitude

of the noise. Non-monotonic Mode settings are:

l

Slope

. Choose Pos, Neg, or Both.

l

Hysteresis is

(set in...). Choose Division, Percent, Absolute.

l

Division/Percent/Absolute

. Enter hysteresis level in the selected unit.

l

Levels are

(set in...). Choose Percent, Absolute, or Pk-Pk%.

l

High/Low Level

. Enter top and bottom thresholds in the selected unit.

Runt Mode

Runt Mode looks for pulses that fail to cross a specified threshhold. You can search for positive-

going or negative-going runts, or both. An adjustable hysteresis band is provided to eliminate noise.

In the case of negative-going runt pulses, the value displayed in the table is the difference (delta) of

the high level of the signal and the runt amplitude (i.e., where the runt bottoms out). This can be

confirmed by placing cursors on the runt pulse and reading the delta Y value in the trace labels. In the

125

Содержание HDO9000





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды