Teledyne HDO9000 Скачать руководство пользователя страница 90

Страница: 90 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Math and Measure

Teledyne LeCroy offers a rich set of standard, pre-programmed tools for the "quickest time to insight"

into the characteristics of acquired waveforms. Most instruments calculate measurements for all

samples in an acquisition, enabling you to rapidly and thoroughly calculate thousands or millions of

parameter values and apply a variety of mathematical functions to the input waveform trace.

Cursors

Cursors are markers (lines, cross-hairs, or arrows) that identify voltage and time values on the

waveform. Use cursors to make fast, accurate measurements of specific points in the waveform.

There are five, standard

cursor types

available.

Vertical (amplitude) cursor readouts appear the trace descriptor box; Horizontal (time) cursor

readouts appear below the Timbebase descriptor box.

Cursors can be placed on math functions whose X-axis has a dimension other than time, such as an

FFT. When there is at least one non-time-domain math trace open, the

Standard Cursors dialog

contains an

X-Axis

control where you can choose the units measured by the horizontal cursors. The

options will be appropriate to the types of function traces open; for example, if there is an FFT trace,

there is an option for Hz. The cursor lines are placed on the traces that normally display X-axis values

in the selected units.

Horizontal Relative cursors.

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды