Teledyne HDO9000 Скачать руководство пользователя страница 52

Страница: 52 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Cable De-Embedding Option

Losses in the cables used in the test setup can reduce the accuracy of your signal (for example,

signal amplitude and risetime), as well as introduce Inter-Symbol Interference. These cable effects

can dramatically alter measurements and potentially create mask test violations.

Cable De-Embedding, available as an option, allows you to quickly specify the characteristics of the

cables (typically found on the cable's data sheet) in your test setup and analyze your signal with the

effects of the cables removed. The compensated signal is a more accurate representation of what

was actually transmitted.

When Cable De-Embedded is installed and selected from the channel pre-processing settings, the

Cable De-Embedding dialog will appear for you to describe the cable being used on the channel.

1. Touch

Vertical > Channel

Setup...

from the menu bar.

2. On the Cx dialog, check

Cable De-Embedding

to display the Cable De-Embedding tab.

3. On the Cable De-Embedding dialog, touch

Cable Specified by

and choose either:

Attenuation Constants.

Enter the cable loss model constants (provided by the manufacturer) in

Cable A1

and

Cable A2

Attenuation Table.

Enter the first set of

Frequency

and

Attenuation

values. Touch

Add

continue adding rows as needed.

Tip:

To edit a row in the table, select the row, change values, then touch

Change

. To

delete a row, select the row and touch

Delete

4. Touch

Delay Specified by

and choose from Propagation Velocity, Nominal Delay, or Dielectric

Constant. Enter the value in the field of the same name.

5. Enter the

Cable Length

in inches.

6. Click

Apply

to initiate the cable de-embedding for the signal on this channel so that the effects

of the cable are removed.

7. To save this cable configuration for future use, touch

File Name [DefaultCable]

and enter a

name, or touch

Browse

and select a file to overwrite. To reload previously saved

configurations, browse to the file, then touch

Load

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды