Teledyne HDO9000 Скачать руководство пользователя страница 109

Страница: 109 / 188

Math and Measure

Trend

A Trend is a plot composed of a series of parameter measurements in the order the measurements

were taken. The vertical units are those of the source parameter, the horizontal unit is measurement

number. The Trend contains a single value for each measurement. Trends are especially useful for

visualizing the history of a parameter over an extended period of time or over multiple acquisitions.

1. Open the parameter setup (P

) dialog for the measurement you wish to histogram.

A quick way to do this is to touch the measurement table cell.

2. Touch the

Trend button

at the bottom of the Px dialog and choose the function location (

) in

which to display the plot. The Trend opens in a new grid along with its function descriptor box.

3. Touch the new

Trend descriptor box

to display the F

dialog, then open the

Trend subdialog

4. Choose a computation

Mode

of All (plots multiple points per acquisition) or Average (plots one

point per acquisition). Enter the number of measured

Values to Trend

5. To rescale the Trend, uncheck

Auto Find Scale

and enter the new

Center

and

Height/div

values.

You can also use

Find Scale

to automatically find suitable values.

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды