manualshive.com logo in svg

Teledyne HDO9000, Руководство оператора

Поделиться
Скачать
Teledyne HDO9000 Скачать руководство пользователя страница 132

HDO9000 High Definition Oscilloscopes Operator's Manual

Memory

The instrument is equipped with four internal memory slots (M

x

) to which you can copy any waveform

that is active on the grid. This is a convenient way to store an acquisition for later viewing and

analysis.

Memories can be used as source inputs for most oscilloscope math and measurements, allowing you

to compare historical data to a live acquisition or perform "what if" modeling on saved acquisitions.

Saving Memories

Store

memories

on the Memory dialogs (M

x

). Memories are created at the same scale as the source

trace, but they can be adjusted independently by using the

zoom factor controls

that appear next to

the M

x

dialogs.

Save Waveform to Memory

Touch the

Add New box

and choose

Memory

until you see an empty memory slot. Drag the descriptor

box of the trace you wish to store onto the M

x

descriptor box.

Note:

Try to choose an empty slot, as anything currently stored in that location will be

overwritten. All memories will state if they are empty or an acquisition is stored there.

1. Press the front panel

Mem button

or choose

Math > Memory Setup

to open the Memories

dialog.

2. Touch the

M

x

tab

corresponding to the memory slot you wish to use.

3. In

Copy from Waveform

, choose the source trace to copy to memory.

4. Touch

Copy Now

.

5. Optionally, check

Trace On

to immediately display the memory. Use the Zoom controls to

adjust the scale of the memory trace.

Save (External) Waveform Files to Memory

Trace (.trc) files saved on other Teledyne LeCroy instruments can also be saved to internal memory.

Use the

Recall Waveform

function to save external files to memory. Then, you can use the

Memories

dialog

to restore them to the touch screen.

122

Содержание HDO9000





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды