Teledyne HDO9000 Скачать руководство пользователя страница 179

Страница: 179 / 188

Certifications

Australia & New Zealand Declaration of Conformity– EMC

The instrument complies with the EMC provision of the Radio Communications Act per the following

standards, in accordance with requirements imposed by Australian Communication and Media

Authority:

AS/NZSCISPR 11:2011RadiatedandConductedEmissions, Group1, Class A.

USTRALIA

/ N

EALAND

ONTACTS

RS Components Pty Ltd.
Suite 326 The Parade West
Kent Town, South Australia 5067

RS Components Ltd.
Unit 30 & 31 Warehouse World
761 Great South Road
Penrose, Auckland, New Zealand

*Visit teledynelecroy.com/support/contact for the latest contact information.

Safety Compliance

EC Declaration of Conformity– Low Voltage

The instrument meets intent of EC Directive 2014/35/EU for Product Safety. Compliance was

demonstrated to the following specifications as listed in the Official Journal of the European

Communities:

EN 61010-1:2010 Safety requirements for electrical equipment for measurement, control, and

laboratory use – Part 1: General requirements

EN 61010-2:030:2010 Safety requirements for electrical equipment for measurement, control, and

laboratory use – Part 2-030: Particular requirements for testing and measuring circuits

The design has been verified to conform to the following limits put forth by these standards:

Mains Power Supply Circuits: Overvoltage Category II, instrument intended to be supplied from

the building wiring at utilization points (socket outlets and similar).

Measuring Circuit Terminals: No rated measurement category. Terminals not intended to be

directly connected to the mains supply.

Unit: Pollution Degree 2, operating environment where normally only dry, non-conductive

pollution occurs. Temporary conductivity caused by condensation should be expected.

U.S. Nationally Recognized Agency Certification

The instrument has been certified by Underwriters Laboratories (UL) to conform to the following

safety standard and bears UL Listing Mark:

UL 61010-1 Third Edition – Safety standard for electrical measuring and test equipment.

169

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды