Teledyne 200A Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 220

Teledyne 200A Скачать руководство пользователя страница 94

Teledyne API Model 200A NO

X

Analyzer Instruction Manual, 02246, Rev. F1

7.2 Manual Zero/Span Check or Calibration with

Zero/Span Valves Option

The Zero/Span valve option can be operated from the front panel keyboard. In the Zero/Span
valve option the zero and span gas come into the valves through ports on the rear panel of the
instrument.

Table 7-5: Manual Zero Calibration Procedure - Z/S Valves

Step Number

Action

Comment

1.

Press CALZ

The analyzer enters the zero calibrate mode. This switches the
sample/cal and zero/span valves to allow zero gas to come in
through the zero gas inlet port in the rear panel.

2.

Wait 10 min

Wait for reading to stabilize at zero value.

3.

Press ZERO

If you change your mind after pressing ZERO, you can still
press EXIT here without zeroing the instrument.

4.

Press ENTR

Pressing ENTR actually changes the calculation equations,
forcing the reading to zero.

5.

Press EXIT

M200A returns to sample mode. Immediately after
calibration, readings do not go into the DAS averages.

Refer to Table 7-3 to enter expected NO and NO

x

values.

Table 7-6: Manual Span Calibration Procedure - Z/S Valves

Step Number

Action

Comment

1.

Press CALS

The M200A enters the calibrate mode from sample mode.
This operates the sample/cal and zero/span valves to allow
span gas to come in through the cal gas inlet port in the rear
panel or optional permeation tube.

2.

Wait 10 min

Wait for reading to stabilize at span value.

3.

Press SPAN

If you change your mind after pressing SPAN, you can still
press EXIT here without spanning the instrument.

4.

Press ENTR

Pressing ENTR actually changes the calculation equations.

5.

Press EXIT

M200A returns to sampling. Immediately after calibration,
data is not added to the DAS averages.

7-6

«
...
92
93
94
95
96
...
»

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов