manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 152 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 152

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 9-2:  Front Panel Warning Messages (Continued) 

Message 

Description 

PMT TEMP WARNING 

PMT temp. out of spec. The PMT temp has its own 
proportional controller on the preamp (01141) board. 
Warnings will occur during initial operation. The warning can 
occur if the 7 pin connector to the interior of the sensor is not 
plugged in. The power connector to the PSM should be 
checked for proper voltage (+15 VDC ± 0.5). 

MOLY TEMP WARNING 

Molycon temp. out of spec. The Moly temp is controlled by 
the CPU. It has a thermocouple with amplifier on the 01086 
Status/Temp board. Because of the high temperature of the 
Moly (315

°

 C), the moly temp warning will tend to be the last 

warning to clear as the instrument is powered on.  

CANNOT DYN ZERO 

Dynamic zero cal. out of spec. The reading of the PMT was 
too high for the ZERO button to appear. Make sure the 
instrument is receiving zero gas. Check for dirty reaction cell. 
Do the factory calibration procedure located in Section 9.1.6. 

CANNOT DYN SPAN 

Dynamic span cal. out of spec. The reading of the PMT was 
too high or low for the SPAN button to appear. Make sure the 
instrument is receiving correct concentration span gas. Make 
sure the expected span concentration is entered. Check for 
dirty reaction cell. Do the factory calibration procedure located 
in Section 9.1.6. 

OZONE GEN OFF 

Ozone Generator is off. See Table 9-11for conditions. 

AZERO WRN XXX.X MV 

The AutoZero circuit compensates for detector dark current, 
and background light. Certain electrical faults cause high 
readings to be added to the filter. First, the cause of the high 
ZutoZero reading should be found and repaired, then wait 15 
minutes for the AutoZero filter to clear itself out. 

A/D NOT INSTALLED 

V/F (00514) board has failed. The V/F board did not respond 
to commands from the CPU. This probably means 1. board not 
seated in socket 2. defective board 3. defective back plane 
connector. 

HVPS WARNING 

High Voltage Power Supply voltage out of limits. Limits are 
400-900 VDC. 

DCPS WARNING 

DC Power Supply voltage out of limits. Limits are 2500  
± 500 mV. 

9-10 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов