Teledyne 200A Скачать руководство пользователя страница 112

Страница: 112 / 220

Teledyne API Model 200A NO

Analyzer Instruction Manual, 02246, Rev. F1

Plot the analyzer NO and NO

responses versus the corresponding calculated concentrations to

obtain the calibration relationships. Determine the straight line of best fit (y = mx + b)
determined by the method of least squares.

After the best-fit line has been drawn for the NO and the NO

calibrations, determine whether

the analyzer response is linear. To be considered linear, no calibration point should differ from
the best-fit line by more than 2% of full scale.

7.8.5.3 GPT - NO

Calibration Procedure

The M200A computes the NO

concentration by subtracting the NO from the NO

concentration.

Unlike analog instruments, this difference is calculated by the M200A's internal computer
software. It is extremely unlikely that the NO

concentration will be in error. Therefore this

procedure is a confirmation that the NO

subtraction algorithm in the computer is operating

correctly.

NOTE

During this procedure do not make any adjustments to the instrument.

Generate an NO concentration near 90% of the URL. Dilution air and O

generator air

flows should be the same as used in the calculation of specified conditions of the dynamic
parameter according to Section 7.8.4. Sample this NO concentration until the NO and NO

responses stabilize. Record the NO and NO

concentrations.

Turn on and adjust the O

generator in the calibrator to produce sufficient O

to decrease

the NO concentration to about 10% of full scale. This will be equivalent to 80% of the URL
of the NO

channel. After the analyzer responses stabilize, record the resultant NO, NO

, and

concentrations.

MOLY CONVERTER EFFICIENCY

IF THE NO

READING SHOULD DROP TO LESS THAN 96% OF ITS STARTING

VALUE DURING THIS STEP, IT INDICATES THE MOLY CONVERTER IS IN NEED
OF TROUBLESHOOTING OR REPLACEMENT. SEE SECTION 7.8.6 FOR FURTHER
DETAILS.

While maintaining all other conditions, adjust the ozone generator to obtain several other

concentrations of NO

evenly spaced between the 80% URL point and the zero point. Record

the NO, NO

, and NO

concentrations for each additional point.

7-24

Содержание 200A





























































































































































































































Результаты поиска

Содержание 200A

Отзывы:

Teledyne 200A, Инструкция по эксплуатации, Страница: 112 / 220

Результаты поиска

Содержание 200A

Отзывы: