manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 49 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 49

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Stability

 

The instrument noise is computed using the standard deviation of the last 10 minutes of data, 
with the value being computed at the end of each NO/ NO

x

 cycle. It is computed for the NO

x

 

channel only. The value only becomes meaningful if sampling a constant concentration for more 
than 20 minutes, so the various software filters can stabilize. The value shown should be 
compared to the value observed in Table 2-1. 

Sample Flow 

The SAMPLE FLOW test function is computed from the pressure measured up-stream of the 
sample flow orifice. The pressure down-stream of the orifice is also checked to assure the 
assumptions of the equation are valid. SAMPLE FLOW will indicate variations in flow caused 
by changes in atmospheric pressure, but will not detect a plugged sample flow orifice. The 
nominal value is 500 ± 50 cc/min. 

Ozone Flow

 

The OZONE FLOW test function is directly measured by a solid state flow meter. Variations in 
this value indicate variations in ozone flow. The nominal value for ozone flow is 60 - 90 cc/min.  

PMT Voltage

 

The PMT VOLTAGE shows the PMT signal at the output of the preamp board. The waveform 
of the PMT voltage can be complex, and vary from near 0 mV when zero gas is in the reaction 
cell to 5000 mV when a high concentration of NO

x

 is being measured. If the PMT reading is 

consistently 5000 mV, that indicates an off-scale reading. Typical readings bounce around, 
which is normal.  

Normalized PMT Voltage

 

Like the PMT Voltage TEST function above, the NORMALIZED PMT VOLTAGE measures 
the PMT signal at the output of the preamp board. The difference here is that several 
normalization functions are applied to this signal before it is displayed. The most important is the 
temperature and pressure compensation factors. If NORM PMT is used as suggested in the 
Factory Calibration Procedure (Section 9.1.6) the M200A will be correctly calibrated. 

AZERO Voltage

 

This test measurement is the AUTOZERO voltage. It indicates the most recent reading from the 
AutoZero circuit. The units are mV and from – 20 to 150 are acceptable. 

5-9 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов