manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 68 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 68

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Communication Protocols 

The RS-232 port can communicate in the following protocols. 

1.

 

Teledyne API protocol – some of the features of this protocol are covered in Section 5.5.2. A 
comprehensive manual is available separately as p/n 01350 RS-232 Programming Notes. 

2.

 

Alternate protocol – this protocol is used for communicating on proprietary networks. 

3.

 

Multidrop protocol – used for communication with multiple Teledyne API instruments on a 
single RS-232 line. A manual is available separately as Teledyne API p/n 01842 Multidrop 
Programming Manual. 

Communication with a modem 

If this bit is set, the instrument will send a setup string out the RS-232 port at power-up. The 
string correctly sets up a US Robotics Sportster Modem. No other brands of modem are 
supported at this time. 

RS-232 Line Errors 

Allows the software to ignore certain errors involving the computation of parity. 

Enable Command prompt 

Setting this bit causes instrument to issue a command prompt after each command output. Useful 
when operating in Terminal Mode. 

5.5.2

  

Command Summary 

The information contained in the rest of this section covers commonly used commands that are 
required to operate the instrument from a remote terminal. If you are going to be writing 
computer programs to communicate with the M200A (i.e. operating the port in COMPUTER 
MODE) we suggest that you order a supplementary manual "The RS-232 Interface", Teledyne 
API part number 01350. This manual describes additional features of the port. 

The Teledyne API RS-232 interface includes multidrop capability, to permit the connection of 
more than one analyzer to a single RS-232 line. To identify each Analyzer, an optional ID 
number is permitted for all commands. If you don’t include the ID number in the command, all 
of the instruments connected to the RS-232 interface will respond. If you include the ID number 
in the command, only the instrument whose ID number matches will execute the command. 

5-28 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов