manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 206 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 206

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

9.3.8.4

The PMT cooler uses a Peltier cooler supplied with DC current from the switching power supply 
in the Power Supply Module. An overall view is shown in Figure 9-9. The temperature is 
controlled by a proportional temperature controller located on the Preamp board. Voltages 
applied to the cooler element vary from 0.1 to 12 VDC. The input voltage from the supply is  
15 VDC. The actual 7

°

 C setpoint will vary ± 1

°

 C due to component tolerances. The 

temperature will be maintained within 0.1

°

 C about the setpoint. The maximum temperature the 

control circuit is able to report is 15

°

 C. The M200A reports this temperature when the unit 

initially powered on. If the temperature fails to drop after 30 minutes, there is a problem in the 
cooler circuit. If the control circuit on the Preamp card is faulty a temperature of -1

°

 C is 

reported

9.3.8.5  High Voltage P.S. 

The HVPS is located in the interior of the Sensor Module, and is plugged into the PMT tube. It 
requires 2 voltage inputs. The first is +15 which powers the supply. The second is the 
programming voltage which is generated on the Preamp Board. This power supply is unlike a 
traditional PMT HVPS. It is like having 10 independent power supplies, one to each pin of the 
PMT. The test procedure below allows you to test each supply. 

Adjustment of the HVPS is covered in the Factory Calibration Procedure in Section 9.1.6. To 
troubleshoot the HVPS: 

1.

 

Turn off the instrument. 

2.

 

Remove the cover and disconnect the 2 connectors at the front of the NO

x

 Sensor 

Module. 

3.

 

Remove the end cap from the sensor. 

4.

 

Remove the HVPS/PMT assembly from the cold block inside the sensor. Un-plug the 

PMT tube. 

5.

 

Re-connect the 7 pin connector to the Sensor end cap, and power-up the instrument. 

6.

 

Use Figure 9-12 to check the voltages at each pin of the supply, and the overall voltage.  

7.

 

Turn off the instrument power, and re-connect the PMT tube, then re-assemble the 

sensor. 

If any faults are found in the test, you must obtain a new HVPS as there are no user servicable 
parts inside the supply. 

  

PMT Cooler 

. 

9-64 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов