Teledyne 200A Скачать руководство пользователя страница 170

Страница: 170 / 220

Teledyne API Model 200A NO

Analyzer Instruction Manual, 02246, Rev. F1

9.2.3 No Response to Sample

Confirm correct operation of analog output by performing Analog Output Step Test in

Section 9.1.3.5.

Confirm general operation of analyzer.

Check for AC Power, Section 9.2.1.

Do flow checks, Section 9.2.2.

Confirm that sample gas contains NO or NO

Check instrument electronics.

Do ELEC TEST procedure in DIAGNOSTIC menu Section 9.1.3.2.

Do OPTIC TEST procedure in the DIAGNOSTIC menu Section 9.1.3.3.

If the M200A passes ET and OT, that means the instrument is capable of detecting light
and processing the signal to produce a reading. Therefore, the problem is in the
pneumatics or ozone generator.

Check ozone generator subsystem. Do diagnostic test of ozone generator subsystem, see

Section 9.3.6.

Check for disconnected electrical cables to sensor module.

9-28

Содержание 200A





























































































































































































































Результаты поиска

Содержание 200A

Отзывы:

Teledyne 200A, Инструкция по эксплуатации, Страница: 170 / 220

Результаты поиска

Содержание 200A

Отзывы: