manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 50 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 50

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

High Voltage Power Supply (HVPS)

 

The HVPS reading is a measure of the scaled-up HVPS programming voltage. The voltage used 
to set the HVPS output is generated on the Preamp board. Its value is between 0 and 1 volt, 
corresponding to a voltage of 0 to 1000 volts out of the HVPS. The HVPS front panel TEST 
measurement should be greater than 450 volts and will typically be around 600-800V. 

DC Power Supply (DCPS)

 

The DCPS voltage is a composite of the 5 and ± 15 VDC voltages in the Power Supply Module. 
This is meant to be a quick indicator to show if the PSM is working correctly. The nominal value 
is 2500 mV ± 200 mV. 

Reaction Cell Temperature

 

This is a measurement of the temperature of the reaction cell. It is controlled by the computer to 
50 ± 1

°

 C. Temperatures outside this range will cause the M200A output to drift. 

Box Temperature 

This TEST function shows the temperature inside the chassis of the M200A. The temperature 
sensor is located on the Status/Temp Board. Typically it runs 2 to 10

°

 C higher than the ambient 

temperature. The M200A has been engineered to maintain stable output over 5 to 40

°

 C ambient 

temperature range.  

PMT Temperature 

The temperature of the PMT is closely controlled by a dedicated proportional temperature 
controller. The nominal set-point is 7 ± 1

°

 C. Readings outside this range will cause instrument 

drift due to gain changes in the PMT detector. 

IZS Temperature

 

The IZS option has an oven for NO

2

 permeation tubes. The oven temperature is nominally 50

°

 C. 

The permeation tube temperature is stable to ± 0.1

°

 C, although it is normal to see the 

temperature on the front panel move ± 0.4

°

 C due to the proximity of the temp sensor to the 

heater. It can be adjusted from the front panel by pressing SETUP-MORE-VARS and selecting 
the IZS_SET item and entering the desired temperature. Using this adjustment, the permeation 
rate of the NO

2

 permeation tube can be adjusted to a desired value. See Section 6.3 for 

information on adjusting the IZS temperature. 

5-10 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов