Teledyne 200A Скачать руководство пользователя страница 86

Страница: 86 / 220

Teledyne API Model 200A NO

Analyzer Instruction Manual, 02246, Rev. F1

If an ammonia permeation tube is being used, substitute the molecular weight of NH

(17

g/mole) for that of NO

The temperature is set at 50.0

C. Check SETUP-MORE-VARS and scroll to the IZS-SET

variable to verify that the temperature is properly set. It should be set to 50

C with over-and-

under temperature warnings set at 49

C and 51

C. There is a 60 cc/min flow across the

permeation tube at all times to prevent build-up of NO

gas in the tubing.

If desired, the output of the permeation tube can be adjusted by adjusting the oven temperature
up or down slightly. The adjust increment is 0.1

C to facilitate small adjustments of the setpoint

temperature.

WARNING

Do not leave instrument turned off for more than 8 hours

without removing the permeation tube. Do not ship the

instrument without removing the permeation tube. The

tube continues to emit NO

, even at room temperature

and will contaminate the entire instrument.

6-6

Содержание 200A





























































































































































































































Результаты поиска

Содержание 200A

Отзывы:

Teledyne 200A, Инструкция по эксплуатации, Страница: 86 / 220

Результаты поиска

Содержание 200A

Отзывы: