manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 146 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 146

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 9-1:  Test Functions 

Test Function 

Factory Set-Up 

Comment 

RANGE 

500PPB 

This is the Range of the instrument. In standard configuration all 3 
outputs have the same range. 
 
Independent range option allows different ranges for each output. 
When enabled, there will be 3 range values displayed. 
 
Auto range option allows 2 different ranges for all outputs, and 
will automatically switch to the other range dynamically as 
concentration values require. The TEST values will show the 
range the instrument is currently operating in, and will 
dynamically display the alternate range as the range changes 
occur. 

STABIL 

Check value in 
Final Test Values 
Table 2-1 

The instrument stability is the Std. Deviation of the last 10 min of 
NO

x

 conc data. It is computed for the NO

x

 channel only. The noise 

value only becomes meaningful if sampling a constant 
concentration for more than 20 minutes. The noise value should be 
compared to the value observed in the factory check-out.  

Faults that cause high noise values are: 

1.

 

Gas leaks 

2.

 

Light leak 

3.

 

Faulty HVPS

 

4.

 

Defective Preamp board 

 

5.

 

Outgassing Moly converter

 

6.

 

PMT recently exposed to room light

 

7.

 

Dirty/contaminated reaction cell

 

8.

 

Mis-calibrated (slope - offset outside of limits)

 

SAMPLE FLW 

500 cc/min 

±

 50 

This is the instrument flow. It is computed using the up stream and 
down stream pressures across the sample flow orifice. This 
method can give a false flow indication if the orifice is plugged 
and the sample pump is creating a pressure drop. It should be 
taken into account when diagnosing instrument faults. 
 
 - A rapid method of determining if the orifice is plugged is to 
disconnect the sample and ozone tubes from the reaction cell, then 
briefly put your finger over the fittings on the cell. You should 
feel the vacuum build up. Also note the difference between the 
high sample flow and the low ozone flow rate. 
 
 - Another reliable method is to attach a rotameter or soap bubble 
flowmeter to the fittings to measure the flows. 
 
Flow rate will change 

±

 a few cc/min due to changes in ambient 

air pressure such as cycling of air conditioning, or passing weather 
fronts. Changing altitude changes the ambient air pressure and 
therefore the sample flowrate. This effect is about 15-20 cc/min 
per 1000 feet of altitude change. If required the output of the 
instrument can be compensated for pressure. See Section 5.3.9, 
Table 9-5. 

(table continued) 

9-4 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов