manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 187 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 187

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

1.

 

After the switches and jumpers are set, turn on instrument power and complete the 

following:  

A.

 

Press SETUP-MORE-DIAG, then press ENTR. Scroll to D/A CALIBRATION, press 

ENTR.  

B.

 

Press ADC to select the first task, which is to calibrate the A/D converter. 

C.

 

Connect a DVM ground lead to TP3-AGND on the V/F board. Connect the positive lead 

to TP9-DAC0. 

D.

 

The M200A will display a voltage near 1% of the voltage range set in the above 

procedure. See Figure 9-4 for a table of approximate expected voltages. Adjust R27 until 
the displayed voltage matches the DVM voltage, then press ENTR. 

E.

 

The M200A will display a voltage near 90% of the voltage range set in the above 

procedure. Adjust R31 until the displayed voltage matches the DVM voltage, then press 
ENTR. This step calibrates the instrument A/D converter to the external DVM. 

F.

 

The M200A will automatically scroll through the DAC output channels, calibrating each 

one. The display will update the progress of the calibration. If operating all analog outputs 
in voltage mode this completes the calibration procedure. 

The calibration of each channel can be checked or recalibrated independently by scrolling the 
PREV-NEXT buttons and pressing CAL for the desired channel. Also a DC offset bias can be 
entered by pressing the OFFSET button for the appropriate channel. 

Calibrating a channel for current loop operation: 

1.

 

BEFORE STARTING, make sure that hardware settings are correct as shown in Table 9-6 
and Table 9-7. 

2.

 

Calibrate the A/D converter as described in item 2 above, if necessary. 

3.

 

Connect a 250 ohm resistor in series with a current meter to the correct pair of terminals on 
the rear panel, see Table 9-8 for terminal assignments.  

4.

 

In the D/A calibration Menu press CFG, then use PREV-NEXT to select the channel to be 
calibrated. 

5.

 

Press the SET button to select CURR for current loop operation, then press ENTR. 

6.

 

To enter the calibration routine press CAL. 

7.

 

To calibrate the 4 mA zero point, press the UP-UP10 - DN-DN10, then press ENTR. 

8.

 

The M200A will then output 20 mA. Press the UP-UP10 - DN-DN10 buttons to calibrate the 
span point, then press ENTR. 

9.

 

Repeat steps 2-6 for each channel that needs to be calibrated. 

 

9-45 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов