Teledyne 200A Скачать руководство пользователя страница 180 | Manualshive

Страница: 180 / 220

Teledyne 200A Скачать руководство пользователя страница 180

Teledyne API Model 200A NO

X

Analyzer Instruction Manual, 02246, Rev. F1

9.3.2 RS-232 Communications

The M200A uses the RS-232 communications protocol to allow the instrument to be connected
to a variety of computer based equipment. RS-232 has been used for many years and is well
documented. Generally, every manufacturer observes the signal and timing requirements of the
protocol very carefully. Problems arise when trying to specify connectors, and wiring diagrams
that attach the analyzer to various devices.

9.3.2.1 RS-232 Connection

If the RS-232 port is not working, check the following:

Physical Wiring

First is to get the physical wiring hooked up correctly. Refer to Figure 9-3 for the wiring diagram
of the DB-9 plug on the M200A rear panel. There are 2 features that make connecting the wiring
easier. First is the red/green LED’s on the rear panel. The M200A provides the power to run the
red LED, the external equipment will provide the power for the green LED. If the wiring is
hooked up correctly both LED’s will be illuminated. Secondly, there is a DTE-DCE switch, this
switch interchanges pin 2 & 3 on the DB-9 connector. Set the DTE-DCE switch so that both
LED’s are illuminated.

RS-232 Protocol (BAUD rate, Data bits, Parity)

Second is to get the communication protocol for each instrument to match. In Figure 9-3 the
default RS-232 parameters are listed. The BAUD rate can be changed in the software menus
under SETUP-MORE-COMM-BAUD.

Data Communications Software for a PC

You will need to purchase a software package so your computer can transmit and receive on its
serial port. There are many such programs, we use PROCOMM at Teledyne API. Once you set
up the variables in PROCOMM and your wiring connections are correct, you will be able to
communicate with the analyzer.

If connecting to a modem, check the following:

Modems are especially difficult because they may have pins that need to be at certain levels
before the modem will transmit data. The most common requirement is the Ready to Send (RTS)
signal must be at logic high (+5V to +15V) before the modem will transmit. The Teledyne API
analyzer sets pin 8 (RTS) to 10 volts to enable modem transmission. Once the physical
connection has been correctly established, it is necessary to establish the correct software
settings in the modem. If the RS-232 bit field #64 in the VARS menu has been set, the M200A
will transmit a modem setup string when the instrument is powered up. The contents of the string
are set for a US Robotics Sportster modem. We strongly recommend using this model of modem
to avoid modem connection problems.

9-38

«
...
178
179
180
181
182
...
»

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов