Teledyne 200A Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 220

Teledyne 200A Скачать руководство пользователя страница 66

Teledyne API Model 200A NO

X

Analyzer Instruction Manual, 02246, Rev. F1

Table 5-10: RS-232 Switching From Terminal Mode to Computer Mode

Key

Function

Control-T (ASCII 20 decimal)

Switch to terminal mode (echo, edit)

Control-C (ASCII 3 decimal)

Switch to computer mode (no echo, no edit)

If the command line doesn't seem to respond to keystrokes or commands, one of the first things
you should do is send a Control-T to switch the command line interface into terminal mode.
Also, some communication programs remove CTRL-T and CTRL-C characters from the byte
stream, therefore these characters will not be sent to the analyzer. Check your communications
program owners manual.

Entering Commands in Terminal Mode

In terminal mode, all commands must be terminated by a carriage return; commands are not
processed until a carriage return is entered. While entering a command you may use the
following editing keys:

Table 5-11: RS-232 Terminal Mode Editing Keys

Key

Function

CR (carriage return)

Execute command

BS (backspace)

Backspace one character to the left

ESC (escape)

Erase entire line

Words such as T, SET, LIST, etc. are called keywords and are shown on the help screen in
uppercase, but they are not case-sensitive. You must type the entire keyword(s), separated by
spaces; abbreviations are not accepted.

NOTE

To open the help screen, Type "?" and press the Enter key.

5-26

«
...
64
65
66
67
68
...
»

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов