manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 189 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 189

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

9.3.3.2

Several different output voltage ranges can be selected by switchs on the V/F board. See Figure 
9-4 for the switch settings. 

9.3.4  Status/Temp Board 

The Status/Temp Board is a multifunction board that: 

1.

 

Converts the resistance readings of the thermistors to voltages 

2.

 

Conditions the thermocouple voltage for the V/F card 

3.

 

Provides status output circuitry 

4.

 

Provides circuitry for contact closure inputs 

5.

 

Provides circuitry for display brown-out/reset at low line voltage 

6.

 

Provides chip carriers for voltage-to-current modules 

9.3.4.1  Temperature Amplifier Section 

The Status/Temp board (01086) is a multifunction board consisting of 4 thermistor amplifiers 
that monitor: 

1.

 

IZS temperature 

2.

 

Reaction Cell temperature 

3.

 

Box temperature 

4.

 

Spare 

All 4 amplifiers have a single gain control - R34. If necessary, you can adjust the temperature 
values by selecting the BOX TEMP - TEST function and adjusting R34 until the correct box 
temp is shown. Remember that the temperature inside the case runs several degrees higher than 
room temperature, which should be taken into account when setting BOX TEMP. 

The voltages of the thermistor and thermocouple amplifier outputs are brought out to test points 
on the edge of the board. Refer to the schematic 01086 for details. The voltages can also be read 
using the DIAGNOSTIC - SIGNAL I/O feature. See Table 9-4 for details. 

  

Changing Output Voltage Ranges 

9-47 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов