manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 21 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 21

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Step 3 - Review the quality of the calibration: 

Calibration Quality Check Procedure 

Step Number 

Action 

Comment 

1. 

Scroll the TEST 
function menu until 
the NO

x

 SLOPE is 

displayed. 

The SLOPE value for NOx should be 1.0 ± 0.3. If the value is 
not in this range, check Section 7.10 or 9. If the SLOPE value 
is in the acceptable range, the instrument will perform 
optimally. 

2. 

Scroll the TEST 
function menu until 
the NO SLOPE is 
displayed. 

The SLOPE value for NO should be 1.0 ± 0.3. If the value is 
not in this range, check Section 7.10 or 9. If the SLOPE is in 
the acceptable range, the instrument will perform optimally.  
 
NOTE:  
The NO and NOx slopes should be equal within ± 0.1. 

3. 

Scroll the TEST 
function menu until 
the NOx OFFSET is 
displayed. 

The M200A will display the OFFSET parameter for the NOx 
equation. This number should be near zero. A value of 0.0  
± 150 mV indicates calibration in the optimal range. If the 
OFFSET value is outside this range, check Section 7.4 or 9 for 
procedures to correct the OFFSET value to near zero. 

4. 

Scroll the TEST 
function menu until 
the NO OFFSET is 
displayed. 

The instrument will now display the NO OFFSET value. It 
should also have a value near zero (0.0 ± 150 mV). 

 

Step 4 - The M200A is now ready to measure sample gas.

 

 

2-9 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов