manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 19 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 19

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

7.

 

When the instrument is warmed up, re-check the TEST functions against Table 2-1. All 

of the readings should compare closely with those in the Table. If they do not, see Section 
9.1.1. The next task is to calibrate the analyzer. There are several ways to do a calibration, 
they are summarized in Table 7-1. For a preliminary checkout we recommend calibration 
with zero air and span gas coming in through the sample port. The procedure is: 

Step 1 - Enter the expected NO

x

 and NO span gas concentrations: 

Step Number 

Action 

Comment 

1. Press 

 

CAL-CONC-NOx 

This key sequence causes the M200A to prompt for the 
expected NOx concentration. Enter the NOx span 
concentration value by pressing the key under each digit until 
the expected value is set. 

2. 

Press ENTR 

ENTR stores the expected NOx span value. This value will be 
used in the internal formulas to compute subsequent NOx 
concentration values. 

3. Press 

 

CAL-CONC-NO 

In the same CAL-CONC sub menu press the NO button and 
enter the expected NO span value, then ENTR. As before this 
value will be used in the internal formulas to compute the 
subsequent NO concentration values. 

4. 

Press EXIT-EXIT 

Returns instrument to SAMPLE mode. 

5. Press 

 

SETUP-RNGE-
MODE-SING-ENTR

If necessary you may want to change ranges. Normally the 
instrument is shipped in single range mode set at 500 ppb. We 
recommend doing the initial checkout on the 500 ppb range. 

6. Press 

SETUP-RNGE-SET

After SETUP-RNGE-SET, enter 500 and press ENTR. The 
instrument will now be in the 500 ppb range. 

7. 

Press EXIT 

Returns instrument to SAMPLE mode. 

 

2-7 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов