Teledyne 200A Скачать руководство пользователя страница 90

Страница: 90 / 220

Teledyne API Model 200A NO

Analyzer Instruction Manual, 02246, Rev. F1

Table 7-1: Types of Zero/Span Check and Calibration

Section

Type of Cal or Check

Description

7.1

Manual Z/S Check or Calibration
through the sample port

This calibration option uses calibration gas
coming in through the sample port. IZS and
Zero/Span valves do not operate.

7.2

Manual Z/S Check or Calibration with
Z/S Valves Option.

How to operate Zero/Span Valves Option. Can be
used to check or adjust calibration.

7.3

Manual Z/S Check with IZS Option

How to operate IZS option. Can be used to check
or adjust calibration.

7.4

Automatic Z/S Check with Z/S Valves
or IZS Options

Operates Z/S valves or IZS once per day to check
the calibration.

7.5

Dynamic Z/S Calibration with Z/S
Valves or IZS Option

Operates Z/S valves or IZS once per day and
adjusts calibration.

7.6

Calibrate using NO

Permeation Tube

Allows calibration using NO

gas from the IZS

permeation tube.

7.7

Use of Z/S Valves or IZS with Remote
Contact Closure

Operates Z/S valves or IZS with rear panel
contact closures. Without valves or IZS, can be
used to switch instrument into zero or span cal
mode. Used for either checking or adjusting
zero/span.

7.8

EPA Protocol Calibration

Covers methods to be used if data is for EPA
equivalency monitoring.

7.9

Special Calibration Requirements for
Independent Ranges or AutoRanging

Covers special requirements if using Independent
Range or AutoRange.

7.10

Calibration Quality

Information on how to determine if the calibration
performed will result in optimum instrument
performance.

7.11

References

Contains a list of references on quality control
and calibration.

7-2

Содержание 200A





























































































































































































































Результаты поиска

Содержание 200A

Отзывы:

Teledyne 200A, Инструкция по эксплуатации, Страница: 90 / 220

Результаты поиска

Содержание 200A

Отзывы: