Teledyne 200A Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 220

Teledyne 200A Скачать руководство пользователя страница 99

Teledyne API Model 200A NO

X

Analyzer Instruction Manual, 02246, Rev. F1

7.7 Use of Zero/Span Valves or IZS with Remote Contact

Closure

The Zero/Span valve or IZS options can be operated using Remote Contact Closures provided on
the rear panel. See Figure 2-2 for connector location and pinout. When the contacts are closed,
the analyzer will switch to zero or span mode. The contacts must remain closed for at least 1
second, and will remain in zero or span mode as long as the contacts are closed. If Dynamic
Zero/Span is enabled, the calibration is adjusted at the end of the zero or span time, otherwise
zero or span is just checked, not adjusted.

In order to do another remote check, both contact closures should be held open for at least 1
second, then may be set again. Table 7-9 shows what type of check is performed based on the
settings of the two contact closures.

Table 7-9: IZS or Z/S Valves Modes with Remote Contact Closure

Ext Zero CC

Ext Span CC

Operation

Contact Open

Contact Open

State when in SAMPLE mode, normal monitoring

Contact Open

Contact Closed

Span check or calibrate

*

Contact Closed

Contact Open

Zero check or calibrate

*

* Calibrate only if Dynamic Calibration is enabled.

7-11

«
...
97
98
99
100
101
...
»

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов