manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 143 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 143

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

9

  

TROUBLESHOOTING, ADJUSTMENTS 

 

NOTE 

The operations outlined in this chapter are to be  

performed by qualified maintenance personnel only. 

 

This section of the manual contains information on diagnosing and repairing instrument 
performance problems. It contains information on how to use and interpret TEST and 
DIAGNOSTIC data as well as WARNING messages the instrument generates. There is 
information on how to troubleshoot the instrument subsystems. Finally there is information to 
perform adjustments such as DAC calibration procedures. 

This manual provides troubleshooting procedures that address problems to the board level. For 
component level troubleshooting, consult the schematics for the appropriate board in Appendix 
A.1. 

NOTE 

The values of the readings shown on the front panel of the  

instrument may at times read XXXXXX. This means that the  

reading is off scale and therefore meaningless. 

 

General Troubleshooting  

1.

 

If the fault is light on and it stays on after you clear the warning messages, see Section 

9.1.2. 

2.

 

Think of the analyzer as three sections: 

 
Section 1:  Pneumatics - Over 50% of all analyzer problems are traced to leaks in the pump 
assembly, sample filter, instrument internal pneumatics, calibrator or external sample 
handling equipment. Suspect a leak first, and check Section 9.2. 
 
Section 2:  Electronics - data processing section. This can be readily checked out using 
Electric Test in Section 9.1.3.2. 
 
Section 3:  Optics - Optical section consisting of PMT, HVPS, Preamp, and signal 
processing. Refer to Section 9.1.3.3 on use of Optical Test. 

9-1 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов