manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 158 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 158

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 9-4:  Diagnostic Mode - Signal I/O (Continued) 

No. 

Signal 

Control 

Description 

35 

DAC_CHAN_0 

NO 

Output of NO

x

 channel in mV. 

36 

DAC_CHAN_1 

NO 

Output of NO channel in mV. 

37 

DAC_CHAN_2 

NO 

Output of NO

2

 channel in mV. 

38 

DAC_CHAN_3 

NO 

Test Channel output. Not implemented in current 
software. 

39 NOX_CONC 

YES 

NO

x

 DAC programming voltage. The following 4 

signals can be set to output specific voltages to each 
DAC. Use in conjunction with ANALOG OUTPUT 
test to check each DAC output channel. The value 
keyed in should appear on the the appropriate analog 
output channel. This value overrides data being 
written from the analyzer. Value reverts to instrument 
output when function is exited. 

40 

NO_CONC 

YES 

NO DAC programming voltage. See above for 
description. 

41 NO2_CONC 

YES 

NO

2

 DAC programming voltage. See above for 

description. 

42 

TEST_OUTPUT 

YES 

TEST channel programming voltage. See above for 
description. 

 

9.1.3.2  Electric Test 

This function injects a constant voltage between the preamplifier and the buffer amplifier on the 
preamp board. Electric test checks part of the preamp, the V/F and computer for proper 
functioning. The result of electric test should be a smooth quiet signal as shown by constant 
values for the NO, NO

x

 concentrations, the NO

2

 concentration should be near zero. Likewise the 

analog outputs should produce a smooth quiet trace on a strip chart. 

Procedure: 

1.

 

Scroll the TEST function to PMT. 

2.

 

Press SETUP-MORE-DIAG, then scroll to ELECT TEST by pressing the NEXT button. 

When ET appears, press ENTR to turn it on. 

9-16 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов