manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 60 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 60

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

5.3.5  Password Enable 

If password protection is enabled, a password is required to access calibration or setup menus. In 
the VARS menu a password is always required. To enable passwords press SETUP-PASS-ON. 
A list of passwords is in Table 5-6. 

Table 5-6:  Calibrate, Setup Passwords 

Password Usage 

Password 

Calibration Password  

Use to get into CAL menus 

512, 101 

Setup Password  

Use to get into SETUP menus 

818, 101 

 

5.3.6  Time of Day Clock 

The instrument has an internal time of day clock. The time of day can be set by pressing SETUP-
CLOCK-TIME and entering the time in 24hr format. In a similar manner the date can be entered 
by pressing SETUP-CLOCK-DATE and entering the date in a dd-mmm-yy format. 

If you are having trouble with the clock running slow or fast, the speed of the clock can be 
adjusted by selecting the CLOCK_ADJ variable in the SETUP-MORE-VARS menu. The units 
of CLOCK_ADJ are seconds per day.  

The M200A software and hardware has been designed and tested to operate properly during the 
year 2000 calendar rollover. 

5.3.7  Diagnostic Mode 

The M200A Diagnostic Mode allows additional tests and calibrations of the instrument. These 
features are separate from the TEST functions because each DIAG function has the ability to 
alter or disable the output of the instrument. While in DIAG mode no data is placed in the DAS 
averages. Details on the use of Diagnostic mode are in Section 9.1.3. 

5.3.8  Communications Menu 

The COMM menu allows the RS-232 BAUD rate to be set. To set the BAUD rate press SETUP-
MORE-COMM-BAUD, select the appropriate BAUD rate, then press ENTR.  

The instrument ID number can also be set. This ID number is attached to every RS-232 message 
sent by the M200A. To set the ID press SETUP-MORE-COMM-ID and enter a 4 digit number 
from 0000-9999, then press ENTR. 

5-20 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов