Teledyne 200A Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 220

Teledyne 200A Скачать руководство пользователя страница 4

Teledyne API Model 200A NO

X

Analyzer Instruction Manual, 02246, Rev. F1

5.3.1 Configuration Information (CFG)......................................................................................... 5-14
5.3.2 Automatic Calibration (AutoCal) ......................................................................................... 5-14
5.3.3 Data Acquisition System (DAS)........................................................................................... 5-14
5.3.4 Range Menu .......................................................................................................................... 5-16
5.3.5 Password Enable ................................................................................................................... 5-20
5.3.6 Time of Day Clock................................................................................................................ 5-20
5.3.7 Diagnostic Mode................................................................................................................... 5-20
5.3.8 Communications Menu......................................................................................................... 5-20
5.3.9 Variables Menu (VARS) ...................................................................................................... 5-21
5.3.10 M200A Operating Modes ................................................................................................... 5-21

........................................................................................................................... 5-22

....................................................................................................................... 5-23

5.5.1 Setting Up the RS-232 Interface ........................................................................................... 5-24
5.5.2 Command Summary ............................................................................................................. 5-28
5.5.3 TEST Commands and Messages .......................................................................................... 5-32
5.5.4 WARNING Commands and Messages................................................................................. 5-33
5.5.5 CALIBRATION Commands and Messages ......................................................................... 5-34
5.5.6 DIAGNOSTIC Commands and Messages............................................................................ 5-36
5.5.7 DAS Commands and Message.............................................................................................. 5-37
5.5.8 Internal Variables.................................................................................................................. 5-39

6 OPTIONAL HARDWARE AND SOFTWARE....................................................... 6-1

.................................................................................................................. 6-1

....................................................................................................................... 6-1

(IZS) ........................................................................................................... 6-3

....................................................................... 6-3

......................................................................................................................... 6-5

.................................................................................................. 6-8

7 CALIBRATION AND ZERO/SPAN CHECKS....................................................... 7-1

...................... 7-4

ALIBRATION WITH

....................... 7-6

............................................................................. 7-7

..................................................................................................... 7-7

.............................................................................................. 7-7

......................................................................................... 7-9

...................................... 7-11

..................................................................................................... 7-12

7.8.1 Calibration of Equipment...................................................................................................... 7-12
7.8.2 Calibration Gas and Zero Air Sources .................................................................................. 7-14
7.8.3 Data Recording Device ......................................................................................................... 7-15
7.8.4 Gas Phase Titration (GPT) System ....................................................................................... 7-16
7.8.5 Dynamic Multipoint Calibration Procedure ......................................................................... 7-20
7.8.6 Moly Converter Efficiency ................................................................................................... 7-25
7.8.7 Calibration Frequency........................................................................................................... 7-27
7.8.8 Other Quality Assurance Procedures .................................................................................... 7-27

iv

«
...
2
3
4
5
6
...
»

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов