manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 95 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 95

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

7.3  Manual Zero/Span Check with IZS Option 

The Internal Zero/Span (IZS) system can be operated from the front panel keyboard. When the 
M200A is in the SAMPLE mode, and the IZS option is installed, the CALS (Calibrate-Span) or 
CALZ (Calibrate-Zero) buttons will be visible. When the buttons are pressed, valves are 
switched to allow zero air or NO

2

 gas to be input into the instrument. 

It is not possible to calibrate the M200A on a NO

2

 permeation tube unless the CAL-ON-NO2 

option is enabled. This is because the NO

2

 permeation tube contains no NO gas. We recommend 

a NO tank with calibration certificate for complete calibration or see CAL-ON-NO2 Section 7.6. 

To do a manual zero check with the IZS Option, press CALZ, then wait about 10 minutes for the 
zero reading to stabilize. The zero value in the display, and analog output is the zero value. Press 
EXIT to return to SAMPLE mode. This procedure does not change the zero calibration of the 
instrument. 

To do a manual NO

2

 check, press CALS, then wait about 10 minutes for the NO

2

 reading to 

stabilize. The concentration value in the display, and analog output is the span value. Press EXIT 
to return to SAMPLE mode. This procedure does not change the span calibration of the 
instrument. 

7.4  Automatic Zero/Span Check 

In a typical air monitoring application it is desirable to have the analyzer automatically check 
(AUTOCAL) its calibration each day. If equipped with Z/S valves or the IZS option, the M200A 
can provide a daily calibration check. There are many operational choices such as moving the 
check backwards or forwards a fixed time each day. 

Setup of the AUTOCAL is covered in Table 6-2. 

7.5  Dynamic Zero/Span Calibration 

The AUTOCAL system described above can also optionally be used to calibrate the instrument 
once each 24 hours. The dynamic calibration is enabled by setting Dynamic Zero/Span buttons 
to ON. 

Before proceeding with enabling DYNAMIC Z/S you must setup the AUTOCAL feature. 
Enabling AUTOCAL is described in Table 6-2. To enable DYNAMIC Zero/Span Calibration: 

7-7 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов