manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 97 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 97

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

7.6

  

Calibrate on NO

2

 Permeation Tube 

If the M200A is equipped with the IZS option, is possible to span the instrument on the 
permeation tube. If this feature is enabled, the instrument internal valves are set so that gas is 
routed through the permeation tube, then the moly converter, thus producing NO gas. The 
software is programmed to use this known NO gas concentration to span both the NO and NO

x

 

channels of the instrument. Thus, if CAL-ON-NO2 is enabled, the CALS button now will span 
both the NO and NO

x

 channels of the instrument. 

CAUTION 

This feature has some unexpected side effects. 

 

tration 

us 

tration of NO gas in the NO and NOx channels, and 

reports a NO  concentration of zero.  

disabled so that NO

2

 concentrations are reported correctly. See Table 7-8 to enable this feature. 

 

If CAL-ON-NO2 is enabled and you do a SPAN CHECK or SPAN CAL, the NO

2

 concen

will be reported as ZERO! This is because all of the NO

2

 gas is being routed through the 

molybdenum converter during both the NO and NO

x

 portions of the measurement cycle. Th

the instrument sees the SAME concen

2

As long as CAL-ON-NO2 is enabled the instrument will never report any NO

2

 during span 

calibration. This feature should be enabled only when a calibration is desired, otherwise leave it 

NOTE 

Note that this method of calibration is NOT approved by the USEPA. 

Permeation tubes are known to change as temperatures are cycled,  

and as they age. Also, this calibration relies on the moly converter  

to be working properly. (Converter efficiency can be compensated  

by enabling the Converter Efficiency option.) It is recommended that  

if CAL-ON-NO2 is used, the instrument calibration be checked  

frequently by independent means to assure accurate data. 

 

7-9 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов