manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 197 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 197

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 9-11:  Ozone Generator Control Conditions 

Condition 

Description 

Ozone 
Generator 

1 

Manual override off (

SETUP-MORE-DIAG-OZONE GEN

). 

OFF 

2 

Manual override on. 

ON 

3 

Ozone flow below low warning limit for 5 minutes (

OFLOW_SET

 

setup variable). 

OFF 

4 

Instrument powered on for more than 30 minutes. 

ON 

5 

Instrument powered off for less than 1 hour 

and

 ozone generator was 

on when instrument was powered off. 

ON 

6 

Ozone flow above low warning limit for 0.5 minutes 

and

 condition 4 

or 5 is true. 

ON 

 

NOTE 

The ozone generator is independently controlled in the SIGNAL I/O, OPTIC 

TEST, and ELECTRICAL TEST diagnostics. After exiting these diagnostics, 

the ozone generator is restored to the state specified by the above conditions. 

 

9.3.6.1  PermaPure Drier 

The PermaPure drier is constructed of 2 concentric tubes. The inner tube is a special material 
that has an affinity for water vapor. The outer annulus is evacuated by the instrument pump. This 
creates a concentration gradient causing water in ambient air to diffuse into the outer annulus, 
thus the air in the inner tube becomes progressively drier as it progresses down the tube. 

Due to the large number of connections and fittings on the drier, the most common drier fault is 
leaks. Before proceding with any other procedures check the drier for leaks. 

Occasionally the drier gets contaminated. The manufacturer of the drier recommends replacing 
the drier rather than trying to clean it. If cleaning is chosen, the following options are available: 

1.

 

Dirt - Clean any solids from dryer inlet by brushing. Use clean dry air to blow any loose 

particles from the inlet. Deionized water or dilute (5-10% conc HCl in deionized water) 
hydrochloric acid can be passed through the dryer. This should be done only with the dryer 
and HCl at room temperature. 

2.

 

Organic liquids and freons - Rinse the inner and outer tubes using 1,1,1 trichlorethane. 

Follow the solvent with dry air to purge the solvent. 

3.

 

Inorganic salts and oxgenated hydrocarbons can be removed by rinsing with 10% nitric 

acid at 50

°

 C. 

9-55 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов