manualshive.com logo in svg

Teledyne 200A, Инструкция по эксплуатации, Страница: 93 / 220

Поделиться
Скачать
Teledyne 200A Скачать руководство пользователя страница 93

Teledyne API Model 200A NO

X

 Analyzer Instruction Manual, 02246, Rev. F1 

 

Table 7-3:  Enter Expected Span Gas Concentrations Procedure 

Step Number 

Action 

Comment 

1. Press 

 

CAL-CONC-NOX 

This key sequence causes the M200A to prompt for the 
expected NO

x

 concentration. 

 
Enter the NO

x

 span concentration value by pressing the key 

under each digit until the expected value is set. This menu can 
also be entered from CALS or CALZ. 

2. 

Press ENTR 

ENTR stores the expected NO

x

 span value. 

3.  

Press  
CAL-CONC-NO 

Now enter the expected NO span concentration as in step one.

4. 

Press ENTR 

Pressing ENTR stores the NO span value and returns the 
prompt to the CONC menu. 

5. 

Press EXIT 

Returns instrument to SAMPLE mode. 

 

If desired, compensation for moly converter efficiency (CE) can be included in the NO

x

 

concentration calculation. The CE must be entered prior to calibration. Refer to Section 7.8.6 for 
the CE procedure. 

Table 7-4:  Manual Span Calibration Procedure - Span Gas thru Sample Port 

Step Number 

Action 

Comment 

1. 

Press CAL 

The M200A enters the calibrate mode. NO span gas should be 
fed to the sample port. 

2. 

Wait 10 min 

Wait for reading to stabilize at span value. 

3. 

Press SPAN 

If you change your mind after pressing SPAN, you can still 
press EXIT here without spanning the instrument. 

4. 

Press ENTR 

Pressing ENTR actually changes the calculation equations and 
causes the instrument to read the NO and NO

x

 span 

concentrations. 

5. 

Press EXIT 

M200A returns to sampling. Immediately after calibration, 
data is not added to the DAS averages. 

7-5 

Содержание 200A





























































































































































































































Отзывы:

Нет отзывов