manualshive.com logo in svg

Suzuki WagonR+ RB310, Руководство по обслуживанию


Поделиться
Скачать
background image

IMPORTANT

WARNING/CAUTION/NOTE

Please  read  this  manual  and  follow  its  instructions  carefully.  To  emphasize  special  information,  the  words

WARNING, CAUTION

 and 

NOTE

 have special meanings. Pay special attention to the messages highlighted by

these signal words.

WARNING:
Indicates a potential hazard that could result in death or injury.

CAUTION:
Indicates a potential hazard that could result in vehicle damage.

NOTE:
Indicates special information to make maintenance easier or instructions clearer.

WARNING:
This service manual is intended for authorized Suzuki dealers and qualified service mechanics only.
Inexperienced mechanics or mechanics without the proper tools and equipment may not be able to
properly perform the services described in this manual.
Improper repair may result in injury to the mechanic and may render the vehicle unsafe for the driver
and passengers.

WARNING:
For vehicles equipped with a Supplemental Restraint (Air Bag) System:
• Service  on  and  around  the  air  bag  system  components  or  wiring  must  be  performed  only  by  an

authorized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under
“General Description” in air bag system section in order to confirm whether you are performing ser-
vice on or near the air bag system components or wiring. Please observe all WARNINGS and “Ser-
vice Precautions” under “On-Vehicle Service” in air bag system section before performing service
on or around the air bag system components or wiring. Failure to follow WARNINGS could result in
unintentional activation of the system or could render the system inoperative. Either of these two
conditions may result in severe injury.

• If the air bag system and another vehicle system both need repair, Suzuki recommends that the air

bag system be repaired first, to help avoid unintended air bag system activation.

• Do not modify the steering wheel, instrument panel or any other air bag system component (on or

around air bag system components or wiring). Modifications can adversely affect air bag system
performance and lead to injury.

• If the vehicle will be exposed to temperatures over 93°C (200°F) (for example, during a paint baking

process), remove the air bag system components (air bag (inflator) modules, SDM and/or seat belt
with pretensioner) beforehand to avoid component damage or unintended activation.

Содержание WagonR+ RB310















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WagonR+ RB310

Lancia Y Owner'S Handbook Manual preview
Y
Бренд: Lancia Страницы: 191
Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Бренд: Cadillac Страницы: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Бренд: Cadillac Страницы: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Бренд: Cadillac Страницы: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Бренд: Cadillac Страницы: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Бренд: Cadillac Страницы: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Бренд: Cadillac Страницы: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Бренд: Cadillac Страницы: 438
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Бренд: Jeep Страницы: 6
Yakima K800 Instructions Manual preview
K800
Бренд: Yakima Страницы: 8
Kia 2011 optima Owner'S Manual preview
2011 optima
Бренд: Kia Страницы: 385
Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Бренд: Lincoln Страницы: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Бренд: Volkswagen Страницы: 26
Roadmaster Sterling ALL-TERRAIN 576 Owner'S Manual & Installation Instructions preview
Sterling ALL-TERRAIN 576
Бренд: Roadmaster Страницы: 12
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Бренд: Axxess Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды