manualshive.com logo in svg

Suzuki WagonR+ RB310, Руководство по обслуживанию


Поделиться
Скачать
background image

GENERAL INFORMATION 0A-5

CAUTION:
• Even when the accident was light enough not to cause air bags to activate, be sure to inspect sys-

tem  parts  and  other  related  parts  according  to  instructions  under  “REPAIRS  AND  INSPECTIONS
REQUIRED AFTER AN ACCIDENT” in Section 10B as well as when air bag is deployment.

• When servicing parts other than air bag system, if shocks may be applied to air bag system compo-

nent parts, remove those parts beforehand.

• When handling the air bag (inflator) modules (driver, passenger and side), seat belt pretensioners

(driver and passenger), side sensors or SDM, be careful not to drop it or apply an impact to it. If an
excessive impact was applied, never attempt disassembly or repair but replace it with a new one.

• When grease, cleaning agent, oil, water, etc. has got onto air bag (inflator) modules (driver, passen-

ger  and  side)  or  seat  belt  pretensioners  (drive  and  passenger),  wipe  off  immediately  with  a  dry
cloth.

• Air bag wire harness is included in instrument panel wire harness. Air bag wire harness branched

off from instrument panel wire harness can be identified easily as it is covered with a yellow protec-
tion tube and it has yellow connectors. Be very careful when handling it.

• When  an  open  in  air  bag  wire  harness,  damaged  wire  harness,  connector  or  terminal  is  found,

replace wire harness, connectors and terminals as an assembly.

• Do  not  apply  power  to  the  air  bag  system  unless  all  components  are  connected  or  a  diagnostic

chart requests it, as this will set a diagnostic trouble code.

• Never use air bag system component parts from another vehicle.
• When using electric welding, be sure to disconnect all air bag (inflator) module connectors and pre-

tensioner connectors from air bag wire harness respectively.

• Never expose air bag system component parts directly to hot air (drying or baking the vehicle after

painting) or flames.

• WARNING/CAUTION labels are attached on each part of air bag system components. Be sure to fol-

low the instructions.

• After vehicle is completely repaired, perform “AIR BAG DIAGNOSTIC SYSTEM CHECK” in Section

10B.

Содержание WagonR+ RB310















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WagonR+ RB310

Camoplast T4S User Manual preview
T4S
Бренд: Camoplast Страницы: 60
TBC DPI1K User Manual preview
DPI1K
Бренд: TBC Страницы: 12
Toyota 4Runner 2019 Quick Reference Manual preview
4Runner 2019
Бренд: Toyota Страницы: 52
Q Mobility Group Q Access Alpha GSE 2023 Installation Manual preview
Q Access Alpha GSE 2023
Бренд: Q Mobility Group Страницы: 9
GMC TopKick 2007 Owner'S Manual preview
TopKick 2007
Бренд: GMC Страницы: 430
Softride 26428 Instructions preview
26428
Бренд: Softride Страницы: 4
Gator GRM430EM User Manual preview
GRM430EM
Бренд: Gator Страницы: 6
POOL-LINE 110085 Assembly Instructions preview
110085
Бренд: POOL-LINE Страницы: 2
RBO IT FITS RBO1018 Product Manual preview
IT FITS RBO1018
Бренд: RBO Страницы: 36
Curt Group Aries AL235045 Installation Manual preview
Aries AL235045
Бренд: Curt Group Страницы: 2
SpeedTech Lights STL Boss Quick Start Manual preview
STL Boss
Бренд: SpeedTech Lights Страницы: 2
Wallbox PLP1 Installation Manual preview
PLP1
Бренд: Wallbox Страницы: 21
Chevrolet Chevelle 1965 Owner'S Manual preview
Chevelle 1965
Бренд: Chevrolet Страницы: 55
Volkswagen Passat 2011 Maintenance Manual preview
Passat 2011
Бренд: Volkswagen Страницы: 188
Alu-Cab SH-BKT-RC-TY Fitment Instructions preview
SH-BKT-RC-TY
Бренд: Alu-Cab Страницы: 6
SportRack EXPLORER A90095 Instruction Sheet preview
EXPLORER A90095
Бренд: SportRack Страницы: 6
Mitsubishi MIRAGE Service Manual preview
MIRAGE
Бренд: Mitsubishi Страницы: 300
Huvitech B12HD-HD Manual preview
B12HD-HD
Бренд: Huvitech Страницы: 31

Бренды по названию

Популярные бренды

Загрузить еще бренды