Suzuki EN125-2A Скачать руководство пользователя страница 92

Страница: 92 / 208

Remove the needle valve retainer and needle

valve.

Remove the main jet.

Remove the needle jet.

Remove the pilot jet.

FUEL AND LUBRICATION SYSTEM

4-4

Remove the main air jet.

If foreign matter is caught between the valve seat

and the needle, the gasoline will continue flowing

and cause it to overflow. If the seat and needle are

worn beyond the permissible limits, similar trouble

will occur. Conversely, if the needle sticks, the

gasoline will not flow into the float chamber. Clean

the float chamber and float parts with gasoline. If

the needle is worn as shown in the illustration,

replace it together with a valve seat. Clean the fuel

passage of the mixing chamber with compressed

air.

NEEDLE VALVE INSPECTION

Reassemble the carburetor by reversing the

sequence of disassembling steps.

REASSEMBLY

NOTE:
Place tongue

of diaphragm to carburetor

body properly.

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды