Suzuki EN125-2A Скачать руководство пользователя страница 18

Страница: 18 / 208

2-5

PERIODIC MAINTENANCE AND TUNE-UP PROCEDURES

Fill a washing pan of a proper size with

nonflammable cleaning solvent. Immerse the

element in the cleaning solvent and wash it clean.

Squeeze the cleaning solvent out of the washed

element by pressing it between the palms of

both hands.

Immerse the element in motor oil, and squeeze

the oil out of the element leaving it slightly wet

with oil.

AIR CLEANER ELEMENT

Clean Every 3 000 km

If the air cleaner is clogged with dust, intake

resistance will be increased with a resultant

decrease in power output and an increase in fuel

consumption.

Check and clean the element in the following

manner.

Remove the left frame cover.

Remove the screws and take out the air cleaner

element assembly.

Separate the polyurethane foam element from

the element frame.

NOTE:
When installing the air cleaner case cover,
place the "UP" mark upward.

NOTE:
Do not twist or wring the element because it
will tear or the individual cells of the element
will be damaged.

CAUTION:
Inspect the element carefully for rips, torn
seams, etc. If any damage is noted, replace
the element.

Element

Non-flammable
Cleaning
Solvent

Motor oil

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды