Suzuki EN125-2A Скачать руководство пользователя страница 178

Страница: 178 / 208

FOREWORD

SUZUKI EN125HU is designed to offer superior performance through lightness in weight

and four-stroke power. The new EN125HU represents another major advance made by

SUZUKI in four stroke motorcycles.

This service manual is prepared primarily for experienced mechanics whose job is

inspecting, repairing and servicing SUZUKI motorcycles. Apprentice mechanics and "do-

it-yourself" mechanics will also find it an extremely useful guide.

Model EN125HU, manufactured to standard specifications, is the main purpose of this

manual. However, EN125HU motorcycles distributed in your country might differ in minor

respects from the standard-specifications of EN125HU and, if they do, it is because some

minor modifications (which are of no consequence in most cases as far as servicing is

concerned) has to be made to comply with the statutory requirements of your country.

(Modifications in the 4th paragraph are as follows:)
This manual is for EN125HU motorcycle, which is a variation of EN125-2A for Mexico.

This EN125HU manual, relating only the modifications made on the basis of EN125-2A,

should be used together with "EN125-2A SERVICE MANUAL" (99500H06100-01E).

SUZUKI distributors are timely informed of our technical modifications and improvements

in this model. Please inquire our distributors for information you need.

SUZUKI MOTOR CORPORATION

JIANGMEN DACHANGJIANG GROUP CO., LTD.

Customer Service Department

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды