Suzuki EN125-2A Скачать руководство пользователя страница 3

Страница: 3 / 208

The SUZUKI EN125-2A was designed to offer superior performance through light weight

design and four stroke power. The new EN125-2A represents another major advance by

Suzuki in four stroke motorcycles.

This service manual has been produced primarily for experienced mechanics whose job is

to inspect, repair and service Suzuki Motorcycles. Apprentice mechanics and "do it

yourself " mechanics will also find this manual to be an extremely useful guide.

Model EN125-2A manufactured to standard specifications is the main subject matter of

this manual. However, the EN125-2A machines distributed in your country might differ in

minor respects from the standard-specification EN125-2A and, if they do, it is because

some minor modifications (which are of no consequence in most cases as far as servicing

is concerned) had to be made to comply with the statutory requirements of your country.

This manual contains up-to-date information at the time of its issue. Latermade

modifications and changes will be explained to each SUZUKI distributor in respective

markets, to whom you are requested to make query about updated information, if any.

FOREWORD

SUZUKI MOTOR CORPORATION

JIANG MEN DACHANGJIANG GROUP CO., LTD.

Customer Service Department

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды