Suzuki EN125-2A Скачать руководство пользователя страница 61

Страница: 61 / 208

3-29

ENGINE

CYLINDER HEAD COVER

Thoroughly wipe off oil from the fitting surfaces

of cylinder head.

Fit the two dowel pins to the cylinder head side.

Uniformly apply SUZUKI BOND No.1215 to the

cylinder head surface.

SUZUKI BOND
No.1215

99000-31110

NOTE:
Do not apply SUZUKI BOND No.1215 to the
camshaft end cap.

Fit a gasket to head cover bolt correctly as

shown in Fig.

CAUTION:
Use only new gasket. To prevent oil leakage.

NOTE:
When tightening the cylinder head cover
bolts, position must be at top dead center on
compression stroke.

Lightly tighten the cylinder head cover bolts

diagonally and then, if everything is satisfactory,

tighten securely with a torque wrench to the

specified torque.

Tightening
torque

9 10 N

(0.9 1.0 kg

Apply engine oil to the tachometer driven gear

shaft and then, insert together with sleeve and

tighten the set screw.

Dowel Pin

CAM DRIVE CHAIN TENSIONER

Install cam drive chain tensioner following the

procedure below.

VALVE CLEARANCE

Remove the lock bolt

, and spring

Fully insert push rod

into the chain tensioner

by lift the pawl.

Mount the chain tensioner on the cylinder.

Install and tighten the lock nut and spring into

the chain tension.

After tightening the head cover bolts, check and

adjust the valve clearance. Refer to page 2-6

for procedures.

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды