Suzuki EN125-2A Скачать руководство пользователя страница 24

Страница: 24 / 208

2-11

PERIODIC MAINTENANCE AND TUNE-UP PROCEDURES

DRIVE CHAIN

Inspect and Clean Every 1 000 km

DRIVE CHAIN

Visually inspect the drive chain for the below listed

possible malconditions. (Lift the rear wheel by

placing the center stand, and turn the rear wheel

slowly by hand when the transmission in NEUTRAL.)

Inspect for:

Wash the chain with kerosene. If the chain

tends to rust faster, the interval must be

shortened.

After washing and drying the chain, lubricate it

with chain lube or gear oil SAE #90.

Check the drive chain for wear and adjust the

chain tension as follows:

Loosen axle nut

after pulling out cotter pin

and loosen the lock nut

Adjust the drive chain carefully by tightening

the adjuster

Loosen the adjuster

until the chain has 10 20

mm of sag at the middle between engine and

rear sprockets.

The mark

on both chain adjusters must be at

the same position on the scale to ensure that

the front and rear wheels are correctly aligned.

After adjusting the drive chain, tighten the lock

nut

and the axle nut

securely and lock with

CHAIN SAG

Count out 21 pins on the chain and measure the

distance between. If the distance exceeds

259.4 mm, the chain must be replaced.

CHAIN WEAR

Service Limit

Drive chain

20 pitch length

259.4 mm

10-20mm

1 2 3

19 20 21

If any defects are found, the drive chain must be

replaced.

1. Loose pins

2. Damaged rollers

3. Rusted links

4. Twisted or seized links

5. Excessive wear

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды