Suzuki EN125-2A Скачать руководство пользователя страница 156

Страница: 156 / 208

BATTERY

SERVICING INFORMATION

7-4

Complaint

Spark plug become
fouled too soon.

Spark plug electordes
overheat or burn.

Generator does not
charge.

Generator charges,but
charging rate is below
the specification.

Unstable charging.

Starter button is not
effective.

Symptom and possible causes

Remedy

1.Worn piston rings.

2.Pistons or cylinder worn.

3.Excessive clearance of valve stems in valve guides.

4.Worn stem oil seals.

Replace.

Replace by cold type plug.

Tune up.

Adjust.

Retighten.

Adjust carburetor.

Repair or replace or retighten.

Replace.

Repair or retighten.

Replace.

Add distilled water between the

level lines.

Replace the battery.

Generator overcharges.

1.Spark plug too hot.

2.The engine overheats.

3.Defective pick up coil or ignitor unit.

4.Spark plug loose.

5.Mixture too lean.

1.Open or short in lead wires, or loose lead connections.

2.Shorted, grounded or open generator coils.

3.Shorted or panctured regulator/rectifler.

1.Lead wires tend to get shorted or open-circuited

at terminals.

2.Grounded or open-circuited stator coils of generator.

3.Defective regulator/rectifier.

4.Not enough electrolyte in the battery.

5.Defective cell plates in the battery.

or loosely connected

1.Internal short-circuit in the battery.

2.Resistor element in the regulator/rectifier damaged or defective.

3.Regulator/rectifier poorly grounded.

1.Lead wire insulation frayed due to vibration,

shorting.

2.Generator internally shorted.

3.Defective regulator/rectifier.

resulting in intermittent

1.Batttery run down.

2.Defective switch contacts.

3.Brusnes not seating properly on commutator in starter motor.

4.Defective starter relay.

Replace the battery.

Replace.

Clean and tighten ground

connection.

Repair or replace.

Replace.

Recharge or replace.

Replace.

Repair or replace.

Replace.

Complaint

"Sulfation", acidic white
powdery substance or
spots on surfaces of cell
plates.

Symptom and possible causes

Remedy

Add distilled water, if the battery has not been damaged

and "sulfation" has not advanced too far, and recharge.

Replace the battery.

If "sulfation" has not advanced too far, try to restore the

battery by replacing the electrolyte, recharging it fully

with the battery detached from the motorcycle and then

adjusting electrolyte S.G.

1. Not enough electrolyte.

2.Battery caes is cracked.

3.Battery has been left in a run-down

a long time.

4.Contaminated electrolyte (Foreign matter

battery and become mixed

electrolyte.)

condition for

has

enters the

with the

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды