Suzuki EN125-2A Скачать руководство пользователя страница 116

Страница: 116 / 208

CHASSIS

5-20

CAUTION:
Never re-use the brake fluid left over from
the last servcing and stored for long periods.

CALIPER

REMOVAL AND DISASSEMBLY

Disconnect the brake hose from the caliper by

remove the bolt

and catch the brake fluid in a

suitable receptacle (Refer to page 2-13).

Loosen the two pins

of caliper.

Remove the caliper mounting bolts

and take

off the caliper.

CAUTION:
Do not operate the brake lever while
dismounting the caliper.

Remove the bracket.

Pull out the pins.

Remove the brake pads.

Place a rag over the piston to prevent popping

up. Force out the piston by using air gun.

CAUTION :
Do not use high pressure air to prevent
piston damage.

Remove the piston, piston boot and piston seal.

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды