Suzuki EN125-2A Скачать руководство пользователя страница 137

Страница: 137 / 208

Remove the spark plug from the cylinder. Install

the plug cap and place the spark plug on the

cylinder head.

Remove the seat and disconnect the lead wire

from the pick-up coil.

Turn the ignition switch ON.

The ignitor unit is in good condition if the follow-

ing is observed.

Connect

probe of SUZUKI Pocket Tester (x1

range) with Green lead wire on the ignitor side and

probe with Blue lead wire.

Next connect

probe with Blue lead wire on the

ignitor side and

probe with Green lead wire .

The moment the tester probes are connected, the

spark plug sparks.

IGNITOR UNIT

Pocket tester

09900-25002

NOTE:
This checking presupposes that the ignition
coil used for checking is a good one.

ELECTRICAL SYSTEM 6-4

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды