Suzuki EN125-2A Скачать руководство пользователя страница 56

Страница: 56 / 208

ENGINE

3-24

The following are reminders for piston installation:

PISTON

Rub a small quantity of SUZUKI MOLY PASTE

onto the piston pin.

Place a clean rag over the cylinder base to

prevent piston pin circlip from dropping into

crankcase, and then fit the piston pin circlip with

long-nose pliers.

CAUTION:
Use a new piston pin circlip to prevent circlip
failure which will occur with a bent one.

When fitting the piston, turn hole on the piston

head to exhaust side.

Before mounting the cylinder, oil the big end and

small end of the conrod and also the sliding

surface of the piston.

CYLINDER

Fit dowel pins

to crankcase and then fit gasket.

CAUTION:
To prevent oil leakage, do not use the old
gasket again, always use new one.

Hold each piston ring with the piston rings

properly spaced and insert them into the cylinder.

Check to insure that the piston rings are

properly inserted into the cylinder.

NOTE:
When mounting the cylinder, after attaching
camshaft drive chain

, keep the camshaft

drive chain taut. The camshaft drive chain
must not be caught between cam drive chain
sprocket and crankcase when crankshaft is
rotated.

NOTE:
There is a holder for the bottom end of the
cam chain guide cast in the crankcase. Be
sure that the guide is inserted properly or
binding of the cam chain and guide may
result.

SUZUKI MOLY PASTE

99000-25140

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды