Suzuki EN125-2A Скачать руководство пользователя страница 19

Страница: 19 / 208

PERIODIC MAINTENANCE AND TUNE-UP PROCEDURES

2-6

Excessive valve clearance results in valve noise

and insufficient valve clearance results in valve

damage and reduced power. At the distances

indicated above, check and adjust the clearance

to the following specification.

The procedure for adjusting the valve clearance

is as follows:

Remove the seat and fuel tank.

Remove the tachometer cable.

Remove the left cap of the cylinder head cover.

Remove spark plug, valve inspection caps

and valve timing inspection plug

Remove the magneto cover cap

and rotate

the magneto rotor with the 14 mm box wrench to

set the piston at (TDC) of the compression

stroke.

(Rotate the rotor until the "l line on the rotor is

aligned with the center of hole on the crankcase.)

Insert the thickness gauge to the valve stem

end and the adjusting screw on the rocker arm.

Remove the right cap of the cylinder head cover.

NOTE:
Valve clearance is be checked when the
engine is cold.
Both the intake and exhaust valves must be
checked and adjusted when the piston is at
Top-Dead-Center (TDC) of the compression
stroke.

VALVE CLEARANCE

Inspect initial 1 000 km and Every 4 000 km

Thickness gauge

09900-20803

Valve clearance specifications

IN.

EX.

0.04 0.07 mm

0.13 0.18 mm

-
-

If clearance is off the specification, bring it into

the specified range by using the special tool.

Tappet adjust driver

09917-13210

Reinstall spark plug, valve inspection caps,

cylinder hand cover caps, tachometer cable, valve

timing inspection plug and magneto cover cap.

Содержание EN125-2A

















































































































































































































Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды

Suzuki EN125-2A, Руководство по обслуживанию

Результаты поиска

Содержание EN125-2A

Отзывы:

Похожие инструкции для EN125-2A

Бренды по названию

Популярные бренды