Suzuki EN125-2A Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 208

background image

7-1

SERVICING INFORMATION

TROUBLESHOOTING

ENGINE

Complaint

Engine will not start
or is hard to start.

Engine stalls easily.

Noisy enigne.

Symptom and possible causes

Remedy

Compression too low

Plug not sparking

No fuel reaching the carburetor

1. Valve clearance out of adjustment
2. Worn valve guides or poor seating of valves.
3. Valves mistiming.
4. Piston rings excessively worn.
5. Worn-down cylinder bore.
6. Poor seating of spark plug.
7. Starter motor cranks but too slowly.

1. Fouled spark plug.
2. Wet spark plug.
3. Defective pick up coil.
4. Defective ignitor unit.
5. Defective ignition coil.
6. Open or short circuit in high-tension cord.

1. Clogged hole in the fuel tank cap.
2. Clogged or defective fuel cock.
3. Defective carburetor float valve.
4. Clogged fuel pipe.
5. Clogged fuel filter.

Adjust.
Repair or replace.
Adjust.
Replace.
Replace or rebore.
Retighten.
Consult "electrical complaints"

Clean or replace.
Clean and dry.
Replace.
Replace.
Replace.
Replace.

Clean.
Clean or replace.
Replace.
Clean or replace.
Clean or replace.

1. Fouled spark plug.
2. Defective pick up coil.
3. Defective ignitor unit.
4. Clogged fuel pipe.
5. Clogged jets in carburetor.
6. Valve clearance out of adjustment.
7. Clogged fuel filter.

Clean.
Replace.
Replace.
Clean.
Clean.
Adjust.
Clean or replace.

Excessive valve chatter

Noise appears to come from piston

Noise seems to come from clutch

Noise seems to come from crankshaft

1. Valve clearance too large.

2. Weakened of broken valve springs.

3. Worn down rocker arm or rocker arm shaft.

1. Piston or cylinder worn down.

2. Combustion chamber fouled with carbon.

3. Piston pin or piston pin bore worn.

4. Piston rings or ring groove worn.

1. Worn splines of countershaft or hub.

2. Worn teeth of clutch plates.

3. Distorted clutch plates, driven and drive.

4. Clutch damper weakened.

1. Worn of burnt bearings.

2. Bjg-end bearings worn and burnt.

3. Thrust clearance too large.

Adjust.

Replace.

Replace.

Replace.

Clean.

Replace.

Replace.

Replace.

Replace.

Replace.

Replace.

Replace.

Replace.

Replace.

«
...
151
152
153
154
155
...
»

Содержание EN125-2A

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EN125-2A

McPherson Strut MIR 1G00

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: HYOSUNG Страницы: 98

Nils Extreme MTW03

Бренд: Abisal Страницы: 21

Бренд: KTM Power Parts Страницы: 7

Бренд: Paaschburg & Wunderlich Страницы: 2

Бренд: hepco & becker Страницы: 4

690 Enduro R 2019

Бренд: KTM Страницы: 274

Бренд: Zontes Страницы: 119

Бренд: Bajaj Страницы: 39

KODIAK YFM70KDXM

Бренд: Yamaha Страницы: 180

Бренд: Yamaha Страницы: 156

RAPTOR 700R 2022

Бренд: Yamaha Страницы: 160

TRACER MTT9K 2019

Бренд: Yamaha Страницы: 122

TT-R125(N) 2000

Бренд: Yamaha Страницы: 508

TT-R125(R) 2002

Бренд: Yamaha Страницы: 510

Бренд: Yamaha Страницы: 610

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды